10 Great Articles On Your Home Plumbing

Delta Faucets and Delta Repairs are some of the most popular videos on You-Tube. I posted three of them, two for their single lever faucets and one for their two handled faucets. In both cases, the removal of the cartridges, ball, seats and springs is necessary for a proper re-build. As far back as I can remember Ive used a thin blade screwdriver, dental pick or even a long needle nose pliers to remove those pesky seats and springs which sometimes can be a pain in the butt to remove. Especially the hot water side, those rubber seats get hard as a rock and literally, break into pieces when trying to remove them. For the most part getting them out is a relatively straight-forward task, but installing the new ones can be tricky at times. You have to drop the springs into a small recess inside the faucet followed by the rubber seat which also has to sit over the spring and into the recess. Often if theres water sitting in the faucet, the rubber seat ends up floating up and out of the recess. A good tip is to remove all the sitting water via a sponge or straw so this problem is avoided.I usually, will thread the rubber seat followed by the spring onto a thin blade screwdriver and use it as a guide to lower them into the recess inside the faucet. This has been the way Ive been doing it ever since I can recall, but recently I found this tool in one of my suppliers catalogs called a Purge-N-Set tool for seats and springs. Needless to say, besides being a tool geek and curious I had to order one and check it out.

http://www.bobsplumbingvideos.com/delta-faucets-delta-repairs-purge-n-set-tool/

What many people are not aware of is just how things work. Ive found that many are completely unaware of plumbing vents and why they are needed. Im going to focus on the drain/waste/vent (DWV) system in this post. Unlike the water supply which uses pressure to move the water, the drains move waste through gravity. In order for this to work they need to have neutral air pressure. If youve ever seen or done the trick where you place a straw in a beverage and seal the top with a thumb or finger, you noticed that the liquid stayed inside the straw when it was lifted up (if it was done properly) but when the seal was released, the liquid spilled out. This is because a vacuum was formed when no air could get in through the top. Drain pipes require a balance of positive and negative pressure or else they trap the water instead of releasing it. In the International Plumbing Code chapter 9 (901.2) it says: The plumbing system shall beprovided with a system of vent piping that will permit theadmission or emission of air the seal of any fixture trap shall not besubjected to a pneumatic pressure differential of more than 1inch of water column (249 Pa) So, behind the wall, your sink should have a vent pipe that starts at or before the point where the drain has its first vertical drop. Up until that point, it needs to be horizontal and slope downward at 1/8 to 1/4 per foot (depending on the size of the pipe).

https://plumbingcodestuff.tumblr.com/post/168596151698/plumbing-diagram-for-someone#_=_

apart. Cut 12-in.-long 12 pickets. Center and tack the first one, then space the others with a 1-1/2-in. block and tack them. Use 1-1/2- in.-galvanized finish nails driven at an angle. Screw the other halves of the top rails to the 12 cleats and center picket. Then screw the 18 bottom rail board through the panel boards into the 28. Use 2-in. deck screws. Screw one pair of upper and lower rails to the cleats with two 2-in.deck screws at each end (Photo 11). Cut a 16 panel board to length, center it in the panel and tack it into place with a couple of 1-1/2 in.

https://www.familyhandyman.com/garden-structures/fences/construct-a-custom-fence-and-gate/view-all/

Back Flow Preventer: A device to prevent back flow, especially into a potable water supply. Required for sprinkler systems, handheld showers, pullout faucet spouts, and kitchen sprayers. Back Pressure: Pressure that resists the flow of fluid in a piping system. Back-siphonage: negative pressure in the piping system which results in backflow. Commonly prevented with a vacuum breaker Gordontheplumber.com Drain cleaning naperville il or air gap. Backup: Overflow of a plumbing fixture due to drain stoppage. Baffle:An object placed in an appliance to change the direction of, or slow down the flow of air, gases or water. Balancing Valve: A water heater valve that controls water flow and balances heat distribution to different locations. Ball Check Valve: A valve that uses a ball to seal against a seat to stop flow in one direction.

https://plumbingcodestuff.tumblr.com/post/157109784533/plumbing-terminology#_=_

You may also be interested to read